Sunday, May 24, 2020

Mostly Work

2020.147

Vegas was nice to visit, if only for a night. That aside, the trip back started reasonable but devolved quickly. Got the welder and some winter gear unloaded; pulled a couple of extra bits of reading material. Then, I started having trouble with my city water line. No matter how hard I cranked, and even changing gaskets, it still leaked. I even cranked so hard that I popped the damn fitting apart. I rushed to the local CW to get a replacement, and hell, let's get a spare too. Get back only discover that, though I knew it was a different brand, the inserted diameter was much larger. Installing one would mean that the face would overlap one of the other taps, which meant that I would have to do a large hole with some sort of mounting bracket. For the interim, I simply swapped the the clean-out with the city connections inside.
Then, as I was typing up my time the morning I was going to leave, I realized that my curb-side rear trailer tire was nearly bald on the exterior. Thus, I had to stop at an auto-parts place, get a jack (why not grab two, just in case), and swap the spare there in the parking lot. As I was rushed to get to Fresno so I could set up and do chores, I hadn't been paying attention much to my read-outs. The truck shifted to 4 on an incline at 65, something I avoid whenever possible. Next thing I know, my engine temp is around 220--it usually rides 210 pretty solid. Instantly I kick off the AC, throw on the defrost, and roll down the windows. I then checked my trans temp which was rolling around 206--I've never seen it above 187. And my last oil change the guys had told me that the fluid was looking a little dirty, so it might run a bit hotter, but I was well due for a tranny flush. So I had to baby it the whole way into Fresno.
The only quick place I could find in Fresno was stupid expensive, and mostly pretentious, and because the entrance isn't properly labeled, my ass kissed hard enough to put a good kink in my rear-curb stabilizer. Err, wait, that was later in San Diego. Fresno was like my regular camp-unpretentious. But this was the first time in a month that Bruce and I had worked together again.
The Sanger gig went off well-enough: Gencor system that uses water mist to reduce the NOx (an old idea that usually is left to simpler minds). We then boogied down to San Diego (with the pretentious park in Escondido), where during our pre-test day, we thought we had it lined out well enough, but there was some glitch in the computer system we had missed, so we battled more than necessary. We were doing okay on the day of, but the guys doing the actual data collection had an oops moment two-thirds the way through, so we would have had to re-do a large chunk of the test (i.e. run tonnage that was likely going to be trashed); or come back the next day. Coupled with this, several customers were hounding Bruce. On the following day, we opted to have him follow-up with these other plants while I did this test, which was actually a blessing since I was able to test this computer glitch and know my parameters. There was a scary moment or two, but we came out alright.
The following week, I moved camp up to Fairplex in Pomona. I've stayed here before, mostly at a quick glance, but nearly everyother place I called wouldn't pick up, or return my calls. The one place that did call back was monthly only. I'm trying to establish a Camp SoCal that is mostly central, bordering Ontario, Chino, and Pomona, both for access to customers, and to build relations with other full-timers. As I learned today though, that is going to be much harder than expected.
After I spent that first weekend catching up on chores, i.e. getting stupid drunk and not doing laundry or dishes, we started the week by getting rained-out at a couple of locations. Then when I was actually able to do a pre-test at the next location, we spend half the day farting around because there was a gas leak somewhere and it was building heavily in the control tower. To the last of my knowledge, the gas techs couldn't properly identify the leak. Once we were actually able to start working again, we wasted the rest of the day tracing back a failed circuit because someone had disconnected the fuse. I spend the rest of this week bouncing from a job on the coast, to one here locally; bouncing between days and nights.
That gig on the coast was nice since I haven't been to the water since I was a kid, and I don't think Nez had ever seen an ocean. So while we were waiting on the word of whether to return or plan on the next day, we went out to Channel Beach N.P. The waves were mild, there weren't too many people around, and the sand was the perfect warm. With my boots on, I got Nez to walk out towards the wet sand and he was fine until a good wave rolled up. I laughed too hard because he spooked suddenly, but didn't really know what to do until the water was already over is paws. While we walked a bit further, I walked to one of the boulder out-croppings and pulled my boots and socks, and rolled-up to dip in.
My feet have always been sensitive to cold water--as a kid, playing on the hospital lawn during the summer, the sprinkler water was too much for me and I would have to give up after 10 minutes. Turns out, the Pacific isn't quite as cold, but it definitely sent a chill through me. But it was nice to then dig my toes into that warm sand. I wish I could have said fuck it, and just spent an hour going from that water to the sand, with no other concerns.
As I have a long weekend for once, I've been trying to knock out several tasks. I got a like-kind city tap, and installed that; did the dishes; got groceries from WinCo...which, be all, is as awesome as expected. I had poked into another WinCo, just a neighborhood version, and hadn't thought much. But the full spread is the real deal. There were a few items I hadn't found, but when I only dropped $70 for what normally ran me $80 or $90, and I was able to support a meaningful company, I'll accept some inconvenience. Rounded out today by getting some random work shit (mostly organizational stuff) and did some laundry.
I got wicked drunk last night, and in tandem with that, I was being friendlier-than-norm with a group nearby: I gave them some beer I wasn't interested in, and asked them to take a cheap dog-bed that Nez isn't interested in. Coupled with the quirky music and habits (I finally pulled out the gas stove last night), they have been super friendly...maybe too much so given our health crisis...but to be fair, I started it. But it beats my neighbor who, though I only saw last weekend, copped an attitude because our doors are facing. Guess there will always be shitbags no matter where you go.

Talked with Tyger finally and it seems my fears were well grounded-he has no real recollection of me. That is to say, he doesn't remember our experiences together. Talking over the phone may be too distant, so maybe presence will help to give that sense of familiarity. Memories aside, he is still the amazing figure that has enjoyed life whenever possible. While his aura has changed over the years, he definitely sounded humbler, more at peace, but I attribute that more to his growth than to his limitations. Less than a month ago, he became a father, so that has been his focus, along with his partner. She is a pretty cute kid...and healthy.
Which seems to be another ticker on my mark-board towards outsider: even the demi-gods that adventured alongside us have given stock to the nuclear idea. Not that I couldn't see him as a father, but when I was invited to his wedding, I was partially mourning: the age of adventure and invisibility was coming to a close as he made vows with this kind and powerful woman. I was overjoyed to be a part of that ceremony, but I had made a plan prior to touchdown, to spend my offtime at a tiki-lounge near my hotel. 
It's not a bad thing that I'm an outsider, that I'm a no-name toiling in the grease and fire. Bodies and minds are needed in these places to keep this mother running. And if I can spit out a few notes that can make people think, well, I had value somewhere. The struggle is fully accepting it--I spend a fair amount of time forgetting my lot, cruising for pretty faces or killing boredum--and doubling down into what could help me create greater potential. Knowing full well that my mommy issues are far from resolved, but not really having a guidebook on how to overcome them, I basically stuff them down which tends to surface periodically, and slow me down.

My hope, as I gain more ground on this nomad life, is to make time for lazy time on the beach, in the mountains; to pick up surfing; to travel outside of the country; to adventure like I once did.



2020.127 Nearly Jacked

2020.127

It's been a whirlwind with one job after another. From SoCal, to the Springs, to Inland NW, back to Phoenix. To whit, fuck me, Arizona is hot. It's only early May and already at 100. No worries though, when we got here we snagged the old man an AC unit for the truck--he's been at least temperate.
Chronologically speaking, let's start from where we left off:
Flagstaff was a nice change, still a bit chilly, but there were my go-to pines blocking the horizon. Poor Nez saw them and was so excited, but we really didn't have the time (or opportunity) to explore. We had made plans, and through a SNAFU on the way to a location, we discovered that the parks were gated shut. But we still walked the road, and I snagged some fallen twigs to leave in the camper (with the intention to get that pine sent...didn't work, but I still have them for some reason).
Bounced back to SoCal to do a couple of stack tests. While I'm glad my hands aren't completely tied, I don't appreciate these miracles they expect. Most companies don't take seriously maintaining a set of run conditions, so when they are expected to meet the requirements, they think we can just wave a wand and make it happen perfectly. Even worse, they seem to forget the last experience, so they assume that we'll give them exactly the numbers they want. This, along with the 1146s (quarterly checks on fluid heaters that run continuously), will be phased out of my repertoire once I really take the reins of this little gig. That said, it's not bad to learn some tricks--just a pain in the ass.
Then I boogied up to Colorado Springs to help with a fuel conversion/start-up. Nobody really told me that this unit was new to the company, but purchased used, so I had no clue what I was getting into. When I stopped in to make sure the pipe work was on-track, I discovered that this outfit we are subbing with really doesn't have a clue: not only were the subs not provided a decent drawing and explanation, they were about to tap the gas into the AC inlet. Not that I am perfect, as I made the executive okay to allow a 10-foot flex to run from the gas train up to the burner: generally speaking, with the corrugation inside the hose, you tend to see a significant pressure drop even after 2 feet; 10 is asking for nothing but trouble.
While this job dragged on forever, it also turned into a mix of adventures and scares. My older sister is based in the area, so I was able to hang with her and her kids a few times. The first day we hung in a wooded regional park on a beautiful day, and she spoiled Nez with a chew-toy. Not sure I've seen him be so committed to something. Because of all this COVID, and the weather dropping on us, we found an alternative place to be the next couple of times. And it was good, almost like old times: chatting, playing Uno, little siblings fighting.
The job itself was a mixed-bag: they had the newest Hauck controls (which the last version I'm relatively familiar with) which had some extra features, but the conditions were nowhere ready for us to run mix. I got the thing lit but, I later found that it was super rich. At one point, because of the snow, I had bought a canopy so I could finish the wiring--my digits were so numb but 1400, I had to call it quits. The super was fine with that since there was only three of us on location.
During this time, of coarse I'm freaking out because I've had frozen pipes and tanks before, and I'm not willing (or able) to walk that line again. It was all well-and-good when out at the Yellow Creek, I could piss in pot and pour it outside, and do my other business either at work or at the truck stop; this camp was so cramped that wasn't really an option. And since my heating system isn't really intertwined with the pipes, I couldn't rely on my ducts alone to keep the pipes thawed. I spent a pretty penny getting heat wrap, a heated inlet hose, and some reflective insulation rolls. The latter I ended up having to throw away as it was "sized" for that camp and probably wouldn't fit elsewhere. I will say though, I was pretty happy at the electric bill being under $20 (I forgot to pay the last bit, but the first week was only $12). Definitely reminds me that I need to get some proper skirting before next winter (and hopefully get the under-carriage enclosed). More on that later.
Then, since I was in the area on my way to Washington, I swung through Evanston. Especially with the bars being closed, it was a friendly reminder of why I had to leave: that town is so slung low that it makes me sick thinking what may-have-been, should I have stayed. They main reason to be there though was to pick-up Grandpa Jack's welder--it's nothing special, in the sense that it's just a basic buzz box, a Marqette Redi-Arc (180A). But it was his out on the ranch and while he used it mostly when necessary, he kept it around. Just like those damned tools of his father's and grandfathers.
During this time, since I knew (or I thought so) that Pappy had a storage unit of stuff leftover of J&B's, I spread the word to the Elders that I was making a tour--I was hoping to help him to economize. Turns out that, while the welder he kept for me, the other stuff he wanted. Luckily, one aunt was the only one that spotted a rocking chair that needed some deep love, so I packed that up as well. Ironically, I also had a left-over pressure regulator from Colorado: it had been shipped to the wrong address and we didn't really know what to do with it just yet.
Ah yes, but before we get too far, I forgot to mention as to another instance I why Wyoming can burn itself alive--it tried to kill me, twice. Heading north from the Springs, there is that little detour we all know of: US 287. My guts told me don't, I know better. But between Google insisting, and the sun breaking the chill, I took a chance. Big mistake. The winds were wicked, as usual, and though it was beautiful out, the temps were below 0 with 40+ winds, which invariably meant ice spots. Here and there I saw them, and I was putting along at 45, just coasting over the humps. One spot in particular, it was an incline with nearly 50 yards of ice, banking to one side. I knew not to throttle it, just use my momentum. Turns out I still had too much throttle.
My nose swung towards the center, presumably because my tail swung to the curb but at a faster rate. Reflex got me to let off the throttle and turn into it: I was inches from jack-knifing. Luckily, between the trailer and the trucks sway and traction system, the trailer laid on the breaks before it got too serious. After that, I crawled at 35. Of coarse, I still swept out later on, taking up the whole road, but my trailer didn't break the plane. Later, in Boise, I stopped and got a equalizer hitch (which I didn't put on until much later).

In Washington, just south of Walla Walla, the plan was to do a fuel switch in Wenatchee, and some follow-up tuning for a couple other plants. This ended up being a continuation of the shit show: subs had no clue, I gave the wrong okay, and nobody was really ready to run mix. I kept at it as best I could but, maybe a couple of weeks prior, I had pulled a filling, trying to offset my chain-smoking with some gum. I put it off for the duration, but it finally caught up to me and I could sense the imminent failure. I've nearly given up on these chompers: I either don't have the money, or the time, to invest in them properly. So, to move forward, I had the defector pulled. Being a molar, and with this lock-jaw, it wasn't an easy extraction. Turns out the damned roots had fused together, so the doc had to drill and break it piece by piece.
I was pretty mopey the few days following that: something about enduring the crumbling of my body, slowly and piecemeal, struck a nerve. Part of it plays into that self-doubt of being sexually appealing (my online dating performance has essentially been a flop, in part due to several factors outside of my control); further, it's just one more tick of worry as I bounce from place to place: how am I going to get 'this' fixed?
Then, I think because I had to get to San Diego, I was able to let some of that go. While the last job wasn't a complete wash as I was able to eye some issues that got missed in engineering, being on the road definitely clears my head. Cutting through norther Cali woods was a big help. San Diego was in-and-out as the district usually shows up for the test, so we steer clear.
Now, I just finished up bouncing between two plants in Phoenix. Optimizations, like seasonal tunes, aren't my favorite, as the operators fight you on the changes, and they want it put back the way you found it--they want to run the burner only one way, with a set profile. For now though, it is good to get the experience (and boost my confidence). But I am looking forward to getting out of this heat. Though, I am swinging through Vegas for a day: I need to drop off this welder, along with my winter gear, maybe pick up some movies and books. It'll only be a night, so not enough time to really eye a true HQ, but I'm hoping to use some of that time to at least get acquainted with the city. It'll probably be at least end of June before I can get back.
After that I'll head: to Fresno to do a stack test; down to San Diego for another Stack Test; head back to LA to do the quarterly stuff. And there is a plethora of other jobs that keep piling up.

While I got a wheeled AC for Nez in the truck, I'm working on setting it up in the camper. I think I have the vent figured out, I just need to make sure I can squeeze it in a certain nook in the bedroom. Not that it is absolutely necessary, especially once I sunblock the windows (just doing the skylight in the shower was a world of difference), but it'll make falling asleep in the early evenings that much easier. With it been over 100 here, in the afternoons I've been trying to wet him down so he can hang outside. He hates baths, and he certainly dislikes being sprayed down (the water is pretty hot coming out of the ground), so it's been a battle. The next investment is to get a collapsible dog pool--I'm sure the first one or two will be junk, but until I actually see how he fits into them (if he is even willing to try), I can't really know. I've also been told that it would be really good to get him some booties--again, don't know if he'll really tolerate it (I'm thinking not), but that blacktop is blistering hot.
I will say, though it's been said plenty before, the RV industry is a scam: the designs are poorly fabbed. I've got a few screws worming loose on the exterior (and their square bits of all things); my tank level indicators worked for maybe the first few weeks; pieces of trim are starting to come off; and that fucking shelf above the stove is going to kill me. Let's forget that I'm tall, even a "average" person will have to hunch to do dishes, and I've clocked my noggin several times, between the side piece, the cabinet door, and the overhang above the counter. I think "style" is over emphasized, and over-priced, but good luck finding a properly designed model that you can roll into any park.
And since we're on this box, that is another gripe I've got: there are enough parks out there that you would imagine that finding one shouldn't be too hard, but between dog restrictions (the breed has no bearing on the temperance, and don't tell me a 5# yapper is more suitable than my old man) and this corona-virus, I'm having to research deeper and harder. As it is, my top-rate has had to increase to $60 as I just can't really find anything within a reasonable distance to location. Granted, a lot of places have been ordered to shutter the gates for the time being, but I don't expect business to go back to normal for the foreseeable future.